Modification du README

README.md

@@ -1,4 +1,3 @@
-
 # Projet ESP
 
 Projet sur une board esp32-8048S043. Le code suivant est fonctionnel. Il s'appuie sur le code officiel du github `esp-idf`.
@@ -18,7 +17,9 @@ Il existe aussi une branch [dev](https://gogs.sincrone.fr/Snorky/esp-project/src
 
 
 
-## Configurer vos accés wifi.
+## Configuration.
+
+### Wifi
 
 Tout se passe dans le fichier `wifi_connect.h`
 
@@ -27,11 +28,23 @@ Modifier les `#define` suivant:
 * #define CONFIG_ESP_WIFI_SSID "YourSSID"
 * #define CONFIG_ESP_WIFI_PASS "YourPASSWORD"
 
+### Déplacer `lv_conf.h`
+
+Il faut déplacer le le lv_conf.h présent dans le répertoire main et le placer dans le répertoire `$PROJET/managed_components/lvgl__lvgl`.
+
+### SDCARD
+
+Le projet requière une sdcard afin de pouvoir initialiser correctement l'affichage. Elle doit être formater en `fat`.
+
+Depuis un terminal, identifier le nom du device puis:
+
+`mkfs.fat /dev/$DEVICE`
+
 ### Build et Flash
 
 Pour build et flasher le board, connectez la via usb et lancer la commande suivante:
 
-`idf.py -p PORT flash monitor`
+`idf.py -p $PORT flash monitor`
 
 Pour sortir du mode monitor saissez les touches ``Ctrl-]`` 
 
@@ -43,101 +56,142 @@ Un peu de doc car la doc ca fait du bien. :)
 
 ## Example de sortie
 
-```
+```I (27) boot: ESP-IDF v5.4 2nd stage bootloader
-I (27) boot: ESP-IDF v5.4 2nd stage bootloader
+I (27) boot: compile time Jan 10 2025 00:28:42
-I (27) boot: compile time Jan  9 2025 18:48:28
 I (27) boot: Multicore bootloader
 I (27) boot: chip revision: v0.2
 I (30) boot: efuse block revision: v1.3
-I (33) boot.esp32s3: Boot SPI Speed : 80MHz
+I (33) qio_mode: Enabling default flash chip QIO
-I (37) boot.esp32s3: SPI Mode       : DIO
+I (38) boot.esp32s3: Boot SPI Speed : 80MHz
-I (41) boot.esp32s3: SPI Flash Size : 2MB
+I (41) boot.esp32s3: SPI Mode       : QIO
-I (45) boot: Enabling RNG early entropy source...
+I (45) boot.esp32s3: SPI Flash Size : 16MB
-I (49) boot: Partition Table:
+I (49) boot: Enabling RNG early entropy source...
-I (52) boot: ## Label            Usage          Type ST Offset   Length
+I (54) boot: Partition Table:
-I (58) boot:  0 nvs              WiFi data        01 02 00009000 00006000
+I (56) boot: ## Label            Usage          Type ST Offset   Length
-I (65) boot:  1 phy_init         RF data          01 01 0000f000 00001000
+I (62) boot:  0 nvs              WiFi data        01 02 00009000 00006000
-I (71) boot:  2 factory          factory app      00 00 00010000 00100000
+I (69) boot:  1 phy_init         RF data          01 01 0000f000 00001000
-I (78) boot: End of partition table
+I (75) boot:  2 factory          factory app      00 00 00010000 00100000
-I (81) esp_image: segment 0: paddr=00010020 vaddr=3c080020 size=189f0h (100848) map
+I (82) boot: End of partition table
-I (106) esp_image: segment 1: paddr=00028a18 vaddr=3fc99a00 size=04948h ( 18760) load
+I (85) esp_image: segment 0: paddr=00010020 vaddr=3c0c0020 size=20f20h (134944) map
-I (110) esp_image: segment 2: paddr=0002d368 vaddr=40374000 size=02cb0h ( 11440) load
+I (113) esp_image: segment 1: paddr=00030f48 vaddr=3fc9cc00 size=051f8h ( 20984) load
-I (113) esp_image: segment 3: paddr=00030020 vaddr=42000020 size=77458h (488536) map
+I (117) esp_image: segment 2: paddr=00036148 vaddr=40374000 size=09ed0h ( 40656) load
-I (204) esp_image: segment 4: paddr=000a7480 vaddr=40376cb0 size=12cb8h ( 76984) load
+I (125) esp_image: segment 3: paddr=00040020 vaddr=42000020 size=b4818h (739352) map
-I (220) esp_image: segment 5: paddr=000ba140 vaddr=600fe100 size=0001ch (    28) load
+I (235) esp_image: segment 4: paddr=000f4840 vaddr=4037ded0 size=0ec3ch ( 60476) load
-I (229) boot: Loaded app from partition at offset 0x10000
+I (246) esp_image: segment 5: paddr=00103484 vaddr=600fe100 size=0001ch (    28) load
-I (229) boot: Disabling RNG early entropy source...
+I (256) boot: Loaded app from partition at offset 0x10000
-I (239) cpu_start: Multicore app
+I (256) boot: Disabling RNG early entropy source...
-I (249) cpu_start: Pro cpu start user code
+I (267) octal_psram: vendor id    : 0x0d (AP)
-I (249) cpu_start: cpu freq: 160000000 Hz
+I (267) octal_psram: dev id       : 0x02 (generation 3)
-I (249) app_init: Application information:
+I (267) octal_psram: density      : 0x03 (64 Mbit)
-I (249) app_init: Project name:     wifi_station
+I (269) octal_psram: good-die     : 0x01 (Pass)
-I (253) app_init: App version:      1
+I (273) octal_psram: Latency      : 0x01 (Fixed)
-I (256) app_init: Compile time:     Jan  9 2025 18:47:46
+I (278) octal_psram: VCC          : 0x01 (3V)
-I (261) app_init: ELF file SHA256:  47f4e7b75...
+I (282) octal_psram: SRF          : 0x01 (Fast Refresh)
-I (266) app_init: ESP-IDF:          v5.4
+I (287) octal_psram: BurstType    : 0x01 (Hybrid Wrap)
-I (269) efuse_init: Min chip rev:     v0.0
+I (291) octal_psram: BurstLen     : 0x01 (32 Byte)
-I (273) efuse_init: Max chip rev:     v0.99 
+I (296) octal_psram: Readlatency  : 0x02 (10 cycles@Fixed)
-I (277) efuse_init: Chip rev:         v0.2
+I (301) octal_psram: DriveStrength: 0x00 (1/1)
-I (281) heap_init: Initializing. RAM available for dynamic allocation:
+I (306) MSPI Timing: PSRAM timing tuning index: 5
-I (287) heap_init: At 3FCA1F08 len 00047808 (286 KiB): RAM
+I (310) esp_psram: Found 8MB PSRAM device
-I (293) heap_init: At 3FCE9710 len 00005724 (21 KiB): RAM
+I (314) esp_psram: Speed: 80MHz
-I (298) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM
+I (331) mmu_psram: Read only data copied and mapped to SPIRAM
-I (303) heap_init: At 600FE11C len 00001ECC (7 KiB): RTCRAM
+I (391) mmu_psram: Instructions copied and mapped to SPIRAM
-I (309) spi_flash: detected chip: gd
+I (392) cpu_start: Multicore app
-I (311) spi_flash: flash io: dio
+I (774) esp_psram: SPI SRAM memory test OK
-W (314) spi_flash: Detected size(16384k) larger than the size in the binary image header(2048k). Using the size in the binary image header.
+I (782) cpu_start: Pro cpu start user code
-I (327) sleep_gpio: Configure to isolate all GPIO pins in sleep state
+I (782) cpu_start: cpu freq: 160000000 Hz
-I (333) sleep_gpio: Enable automatic switching of GPIO sleep configuration
+I (782) app_init: Application information:
-I (340) main_task: Started on CPU0
+I (783) app_init: Project name:     esp_project
-I (360) main_task: Calling app_main()
+I (787) app_init: App version:      fccf92f-dirty
-I (390) Main: ESP_WIFI_MODE_STA
+I (791) app_init: Compile time:     Jan 10 2025 00:28:44
-I (390) pp: pp rom version: e7ae62f
+I (796) app_init: ELF file SHA256:  c74bd4fff...
-I (390) net80211: net80211 rom version: e7ae62f
+I (800) app_init: ESP-IDF:          v5.4
-I (400) wifi:wifi driver task: 3fcabfec, prio:23, stack:6656, core=0
+I (804) efuse_init: Min chip rev:     v0.0
-I (410) wifi:wifi firmware version: 48ea317a7
+I (808) efuse_init: Max chip rev:     v0.99 
-I (410) wifi:wifi certification version: v7.0
+I (812) efuse_init: Chip rev:         v0.2
-I (410) wifi:config NVS flash: enabled
+I (816) heap_init: Initializing. RAM available for dynamic allocation:
-I (410) wifi:config nano formatting: disabled
+I (822) heap_init: At 3FCB1FE8 len 00037728 (221 KiB): RAM
-I (420) wifi:Init data frame dynamic rx buffer num: 32
+I (827) heap_init: At 3FCE9710 len 00005724 (21 KiB): RAM
-I (420) wifi:Init static rx mgmt buffer num: 5
+I (832) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM
-I (420) wifi:Init management short buffer num: 32
+I (838) heap_init: At 600FE11C len 00001ECC (7 KiB): RTCRAM
-I (430) wifi:Init dynamic tx buffer num: 32
+I (843) esp_psram: Adding pool of 7232K of PSRAM memory to heap allocator
-I (430) wifi:Init static tx FG buffer num: 2
+I (850) spi_flash: detected chip: gd
-I (440) wifi:Init static rx buffer size: 1600
+I (853) spi_flash: flash io: qio
-I (440) wifi:Init static rx buffer num: 10
+W (856) i2c: This driver is an old driver, please migrate your application code to adapt `driver/i2c_master.h`
-I (450) wifi:Init dynamic rx buffer num: 32
+I (866) sleep_gpio: Configure to isolate all GPIO pins in sleep state
-I (450) wifi_init: rx ba win: 6
+I (872) sleep_gpio: Enable automatic switching of GPIO sleep configuration
-I (450) wifi_init: accept mbox: 6
+I (879) main_task: Started on CPU0
-I (450) wifi_init: tcpip mbox: 32
+I (899) esp_psram: Reserving pool of 32K of internal memory for DMA/internal allocations
-I (460) wifi_init: udp mbox: 6
+I (899) main_task: Calling app_main()
-I (460) wifi_init: tcp mbox: 6
+I (899) ESP-Display: Turn off LCD backlight
-I (460) wifi_init: tcp tx win: 5760
+I (899) gpio: GPIO[2]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 
-I (470) wifi_init: tcp rx win: 5760
+I (909) ESP-Display: Install RGB LCD panel driver
-I (470) wifi_init: tcp mss: 1440
+I (959) ESP-Display: Initialize RGB LCD panel
-I (470) wifi_init: WiFi IRAM OP enabled
+I (959) ESP-Display: Initialize LVGL library
-I (480) wifi_init: WiFi RX IRAM OP enabled
+I (959) ESP-Display: Allocate separate LVGL draw buffers from PSRAM
-I (510) phy_init: phy_version 680,a6008b2,Jun  4 2024,16:41:10
+I (969) ESP-Display: Register display driver to LVGL
-I (540) wifi:mode : sta (84:fc:e6:6b:a0:cc)
+I (969) ESP-Display: Waiting driver correctly charged!
-I (540) wifi:enable tsf
+I (1979) ESP-Display: Initializing I2C
-I (540) wifi_connect: wifi_init_sta finished.
+I (1979) gpio: GPIO[38]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 
-I (1000) wifi:new:<1,0>, old:<1,0>, ap:<255,255>, sta:<1,0>, prof:1, snd_ch_cfg:0x0
+W (1979) GT911: Unable to initialize the I2C address
-I (1000) wifi:state: init -> auth (0xb0)
+I (1999) gpio: GPIO[18]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:2 
-I (1020) wifi:state: auth -> assoc (0x0)
+I (1999) GT911: TouchPad_ID:0x39,0x31,0x31
-I (1050) wifi:state: assoc -> run (0x10)
+I (1999) GT911: TouchPad_Config_Version:65
-I (1060) wifi:<ba-add>idx:0 (ifx:0, 44:d4:54:71:cb:80), tid:0, ssn:0, winSize:64
+I (2009) Main: ESP_WIFI_MODE_STA
-I (1070) wifi:<ba-add>idx:1 (ifx:0, 44:d4:54:71:cb:80), tid:5, ssn:0, winSize:64
+I (2009) pp: pp rom version: e7ae62f
-I (1080) wifi:connected with Freebox_nomap, aid = 1, channel 1, BW20, bssid = 44:d4:54:71:cb:80
+I (2009) net80211: net80211 rom version: e7ae62f
-I (1090) wifi:security: WPA2-PSK, phy: bgn, rssi: -46
+I (2029) wifi:wifi driver task: 3fcc653c, prio:23, stack:6656, core=0
-I (1100) wifi:pm start, type: 1
+I (2029) wifi:wifi firmware version: 48ea317a7
+I (2029) wifi:wifi certification version: v7.0
+I (2029) wifi:config NVS flash: enabled
+I (2029) wifi:config nano formatting: disabled
+I (2039) wifi:Init data frame dynamic rx buffer num: 32
+I (2039) wifi:Init static rx mgmt buffer num: 5
+I (2049) wifi:Init management short buffer num: 32
+I (2049) wifi:Init dynamic tx buffer num: 32
+I (2059) wifi:Init static tx FG buffer num: 2
+I (2059) wifi:Init static rx buffer size: 1600
+I (2059) wifi:Init static rx buffer num: 10
+I (2069) wifi:Init dynamic rx buffer num: 32
+I (2069) wifi_init: rx ba win: 6
+I (2079) wifi_init: accept mbox: 6
+I (2079) wifi_init: tcpip mbox: 32
+I (2079) wifi_init: udp mbox: 6
+I (2079) wifi_init: tcp mbox: 6
+I (2089) wifi_init: tcp tx win: 5760
+I (2089) wifi_init: tcp rx win: 5760
+I (2089) wifi_init: tcp mss: 1440
+I (2099) wifi_init: WiFi IRAM OP enabled
+I (2099) wifi_init: WiFi RX IRAM OP enabled
+I (2109) phy_init: phy_version 680,a6008b2,Jun  4 2024,16:41:10
+I (2149) wifi:mode : sta (84:fc:e6:6b:a0:cc)
+I (2149) wifi:enable tsf
+I (2149) wifi_connect: wifi_init_sta finished.
+I (2159) wifi:new:<11,0>, old:<1,0>, ap:<255,255>, sta:<11,0>, prof:1, snd_ch_cfg:0x0
+I (2159) wifi:state: init -> auth (0xb0)
+I (2179) wifi:state: auth -> init (0x1c0)
+I (2189) wifi:new:<11,0>, old:<11,0>, ap:<255,255>, sta:<11,0>, prof:1, snd_ch_cfg:0x0
+I (2189) wifi_connect: retry to connect to the AP
+I (2189) wifi_connect: connect to the AP fail
+I (4599) wifi_connect: retry to connect to the AP
+I (4599) wifi_connect: connect to the AP fail
+I (4599) wifi:new:<11,0>, old:<11,0>, ap:<255,255>, sta:<11,0>, prof:1, snd_ch_cfg:0x0
+I (4599) wifi:state: init -> auth (0xb0)
+I (4629) wifi:state: auth -> assoc (0x0)
+I (4669) wifi:state: assoc -> run (0x10)
+I (4709) wifi:connected with TheGame, aid = 7, channel 11, BW20, bssid = 1e:f1:21:fb:e6:1f
+I (4709) wifi:security: WPA2-PSK, phy: bgn, rssi: -27
+I (4719) wifi:pm start, type: 1
 
-I (1100) wifi:dp: 1, bi: 102400, li: 3, scale listen interval from 307200 us to 307200 us
+I (4719) wifi:dp: 1, bi: 102400, li: 3, scale listen interval from 307200 us to 307200 us
-I (1100) wifi:set rx beacon pti, rx_bcn_pti: 0, bcn_timeout: 25000, mt_pti: 0, mt_time: 10000
+I (4729) wifi:set rx beacon pti, rx_bcn_pti: 0, bcn_timeout: 25000, mt_pti: 0, mt_time: 10000
-I (1130) wifi:AP's beacon interval = 102400 us, DTIM period = 1
+I (4749) wifi:<ba-add>idx:0 (ifx:0, 1e:f1:21:fb:e6:1f), tid:0, ssn:0, winSize:64
-I (4400) esp_netif_handlers: sta ip: 192.168.X.X, mask: 255.255.255.0, gw: 192.168.X.X
+I (4769) wifi:dp: 2, bi: 102400, li: 4, scale listen interval from 307200 us to 409600 us
-I (4400) wifi_connect: got ip:192.168.X.X
+I (4769) wifi:AP's beacon interval = 102400 us, DTIM period = 2
-I (4400) wifi_connect: connected to ap SSID:YourSSID password:YourPassword
+I (5769) esp_netif_handlers: sta ip: 192.168.X.X, mask: 255.255.255.0, gw: 192.168.X.X
-I (4410) Main: End of main
+I (5769) wifi_connect: got ip:192.168.X.X
-I (4410) main_task: Returned from app_main()
+I (5769) wifi_connect: connected to ap SSID:YourSSID password:YourPASSWORD
+I (5769) Main: End of main
+I (5779) main_task: Returned from app_main()
 
 ```